"Apps" Prices/Orders - (for your Tablet)

“Enhanced Equal Friction Duct Sizing”, including velocity reduction at larger air quantities.  Also incorporates duct sizing to avoid obstructions.

Quantity Discounts:
1  $12.00 each
2-more 30% off

This program uses a combination of velocity and pressure drop, and includes “Lower First Cost” to “Lower Operating Cost” size selections. 

Quantity Discounts:
1  $11.00 each
2-more 30% off

At the early stages of a project, it is desirable to estimate the static pressure requirements of the fans and air handling units, so preliminary equipment selections and horsepower requirements can be determined.

Quantity Discounts:
1  $19.50 each
2-more 30% off

This program calculates the reheat coil load, based on the input for “Cooling Supply DB” temperature, the “Minimum VAV Air Quantity” for the zone, and the “Calculated Zone Heating Load” for the zone.

Quantity Discounts:
1  $14.00 each
2-more 30% off

Preliminary Cooling Coil Load Calculations can be used to estimate the required Air Handling Unit Cooling Coil capacity.  Preliminary Chilled Water flow rates  for preliminary Pump sizing, preliminary Chiller sizing, preliminary Cooling Tower etc.

Quantity Discounts:
1  $14.50 each
2-more 30% off

At the early stages of a project, it is desirable to estimate the pump head requirements so preliminary pump selections and horsepower requirements can be determined.

Quantity Discounts:
1  $19.00 each
2-more 30% off

When final cost estimates are being prepared, it is important that an accurate accounting for the sheet metal and insulation quantity is provided. 

Quantity Discounts:
1  $10.50 each
2-more 30% off

To accurately size the system expansion tank, it is necessary to calculate the total water volume in the system.  This includes all pipes, heating equipment (boilers, heat exchangers), heating coils, and miscellaneous equipment. 

Quantity Discounts:
1  $12.25 each
2-more 30% off

To accurately size the system expansion tank, it is necessary to calculate the total water volume in the system.  This includes all pipes, cooling equipment (chillers), cooling coils, and any other miscellaneous equipment in the “closed loop” system. 

Quantity Discounts:
1  $11.25 each
2-more 30% off

All of the above HVAC "Apps" in one .zip file package for use on your tablet.  Requires Office Suite-Pro®, or MS Word® & MS Excel®, or equivalent.  (25% Discount)

Quantity Discounts:
1  $93.00 each
2-more 30% off

This “Fixture Unit Calculations” program uses nationally recognized and/or code-approved Fixture Unit values and conversion factors.  Accurately sizing a domestic water system requires determining allowable pressure drop for pipe sizing.

Quantity Discounts:
1  $17.50 each
2-more 30% off

This “Fixture Unit Calculations” program uses 2009 International Plumbing Code Fixture Unit values and conversion factors.   Accurately sizing a domestic water system requires determining allowable pressure drop for pipe sizing.

Quantity Discounts:
1  $17.25 each
2-more 30% off

This “Waste & Vent Sizing Calculations” program uses nationally recognized and/or code-approved Fixture Unit values and sizing formulas.  

Quantity Discounts:
1  $15.50 each
2-more 30% off

This “Waste & Vent Sizing Calculations” program uses 2009 International Plumbing Code Fixture Unit values and sizing formulas.  

Quantity Discounts:
1  $15.25 each
2-more 30% off

Sizing of Roof Drains and Rainwater piping is primarily dependent on Rainfall Rate, Collection Area of the Drain, and slope of the pipes.  

Quantity Discounts:
1  $12.50 each
2-more 30% off

Sizing of Roof Drains and Rainwater piping is primarily dependent on Rainfall Rate, Collection Area of the Drain, and slope of the pipes.  

Quantity Discounts:
1  $12.75 each
2-more 30% off

The program includes conversion of Flush Tank and/or Flush Valve Fixture Unit values to GPM flow rate, which includes the recommended diversity factors.

Quantity Discounts:
1  $9.25 each
2-more 30% off

This program uses a combination of measured lengths, valve and fitting pressure drop factors, and NFPA or Weymouth Formulas to determine accurate pipe sizes. For gas pressures below 1.5 psi.

Quantity Discounts:
1  $16.50 each
2-more 30% off

This program uses a combination of measured lengths, valve and fitting pressure drop factors, and NFPA or Weymouth Formulas to determine accurate pipe sizes. For gas pressures above 1.5 psi.

Quantity Discounts:
1  $16.25 each
2-more 30% off

All of the above UPC and Nat. Gas "Apps" in one .zip file package for use on your tablet.  Requires Office Suite-Pro®, or MS Word® & MS Excel®, or equivalent.  (25% Discount)

Quantity Discounts:
1  $65.50 each
2-more 30% off

All of the above IPC and Nat. Gas "Apps" in one .zip file package for use on your tablet.  Requires Office Suite-Pro®, or MS Word® & MS Excel®, or equivalent.  (25% Discount)

Quantity Discounts:
1  $65.00 each
2-more 30% off

Extensive quality control or "peer review" checklists for HVAC design and review of mechanical construction documents --- to check for coordination between design disciplines, errors and omissions or inconsistencies in the HVAC design; also can be used as a training manual for designers and engineers.

Quantity Discounts:
1  $89 each
2-4   30% off
5-10  40% off

Extensive quality control or "peer review" checklists for Plumbing design and review of mechanical construction documents --- to check for coordination between design disciplines, errors and omissions or inconsistencies in the Plumbing design; also can be used as a training manual for designers and engineers.

Quantity Discounts:
1  $59 each
2-4   30% off
5-10  40% off

7.75%

2 & Up Additional Licenses (of the same title)